| Quantity | Price per item | Discount |
| 3 items | €121.00 | 3% off |
| 5 items | €117.00 | 6% off |
(f)air tightness® EXTRA is a reinforced airtightness and vapour control membrane for suitable internal building-envelope constructions. It combines a polypropylene nonwoven layer, a functional film and an additional reinforcement mesh to provide increased mechanical strength.
Designed for installation on the warm side of the insulation, EXTRA helps limit uncontrolled air leakage and water vapour diffusion into the building structure.
With a nominal sd-value of approximately 20 m and a declared material air permeability of less than 0.004 m³/(m²·h) at 50 Pa, the membrane provides effective vapour control and very low air permeability when correctly installed.
The additional mesh reinforcement provides greater resistance to tensile and tearing forces, making EXTRA particularly suitable for demanding applications involving mineral wool or blown cellulose insulation.
Width: 1.5 m
Length: 50 m
Nominal coverage: 75 m²
Allow for overlaps, trimming and detailing when calculating material requirements.
(f)air tightness® STANDARD is a practical solution for supported internal airtightness and vapour control applications, particularly where relatively lightweight insulation materials are used.
(f)air tightness® EXTRA provides additional mechanical reinforcement and higher vapour diffusion resistance. It is particularly useful where the membrane may be subjected to greater mechanical loads during installation, including applications with mineral wool or blown cellulose insulation.
The appropriate membrane and fixing arrangement must be selected according to the construction, insulation weight, supporting structure and installation conditions.
Install the membrane on the warm side of the insulation according to the approved building-envelope design.
(f)air tightness® GREEN Tape
For suitable membrane overlaps and airtight connections.
(f)air tightness® OR Sealant – 310 ml
For suitable membrane perimeter connections to adjoining construction substrates.
Technical Disclaimer
Any installation details or recommendations provided by Prodomo Ireland are intended as general guidance only and must not be considered as project-specific design approval. The technical feasibility, structural suitability and compliance with applicable building regulations must be assessed and approved by the appointed architect or structural engineer before implementation.
| Property | Value |
| Product | (f)air tightness® EXTRA |
| Construction | Polypropylene nonwoven, functional film and additional reinforcement mesh |
| Roll dimensions | 1.5 × 50 m |
| Nominal roll area | 75 m² |
| Water vapour permeability | 2–3 g/(m²·24 h) |
| sd-value | Approx. 20 m (TDS); ≥ 20 m declared in DoP |
| Material air permeability at 50 Pa | < 0.004 m³/(m²·h) |
| Reaction to fire | Class E |
| Water-tightness | W1 |
| Resistance to water penetration | Meets requirements at 2 kPa |
| Mass per unit area | Approx. 115 g/m² (±10%) |
| Tensile strength – MD (TDS) | ≥ 300 N/50 mm |
| Tensile strength – CD (TDS) | ≥ 245 N/50 mm |
| Tear resistance – MD (TDS) | ≥ 275 N |
| Tear resistance – CD (TDS) | ≥ 295 N |
| Temperature range | −40°C to +80°C; +100°C for limited exposure |
| UV resistance | Up to 4 months under specified laboratory ageing conditions |
| UV exposure during installation | Protect from daylight / UV radiation within 4 weeks |
| Colour | White with black and grey printing |
| Product standard | EN 13984:2013 |
| Declaration of Performance | No. 3-12122018-78 (23 September 2026) |
MD = machine direction; CD = cross direction. Mechanical strength values shown are from the (f)air tightness® EXTRA Technical Data Sheet. The Declaration of Performance contains separately declared values and tolerances. Refer to both documents for full technical information.
Technical specifications for the reinforced EXTRA membrane, including vapour resistance, air permeability, mechanical properties and material characteristics.
Download Technical Data Sheet (PDF)
DoP No. 3-12122018-78, revised 23 September 2026, according to EN 13984:2013.

